A split pipe can push hundreds of gallons into your walls and floors before sunrise. One call connects you with a local plumber who stops the flow, fixes the line, and coordinates the drying side.
Free referral call. You are connected with an independent, licensed and insured local contractor.
A burst pipe is two jobs at once: a plumbing repair and a water problem. The plumbers we route you to handle the first and connect the second, so nothing sits wet while you wait on a second phone call.
We route calls to licensed and insured local plumbers who handle pressurized supply lines as routine work. Ask the plumber for proof of insurance on arrival and confirm any permit your local code requires for the repair.
The dispatcher stays on the line long enough to get your water shut off, then finds an available plumber near you. Your arrival window is confirmed before the call ends, so you know whether to start moving furniture or wait at the door.
You get the price from the contractor in writing before any wall is opened or any pipe is replaced. If opening the wall reveals more damage, they adjust the scope with you first.
The plumbers in our network carry acoustic listening gear, thermal cameras, crimp and expansion tools, pipe freeze kits, and pressure gauges.
No two breaks are the same. The material, where the pipe runs, and the cause of the failure all change what the right fix looks like.
Freeze breaks usually show up in exterior walls, attics, crawl spaces, and garages, often the morning the weather warms and the ice plug thaws. The plumber traces the run to find every split, not just the one spraying, because a pipe that froze once often cracked in more than one spot.
Copper tends to fail two ways: tiny pinholes from water chemistry and wear, or a fitting that cracks under repeated stress. The contractor decides between a sweated repair with a torch and solder, a press fitting, or replacing a longer section if the pipe wall is thin in several places.
With plastic piping, CPVC turns brittle and snaps, PEX fittings can separate, and push-fit connectors can leak once the O-ring or teeth let go. The plumber matches the repair to the system, using crimp or clamp rings, expansion fittings, or solvent-weld CPVC fittings as the material calls for.
Galvanized pipe rusts from the inside out, and once one section bursts, the rest of the run is usually close behind. The contractor can patch the break, then talk with you about repiping in copper or PEX instead of chasing leak after leak.
A warm spot on the floor, a meter that spins with every tap closed, or the sound of running water usually points to a leak under the slab. The plumber uses acoustic listening equipment and thermal imaging to pinpoint the break, then explains the choices: a spot repair through the slab, rerouting the line overhead, or a reroute through the walls.
Some pipes burst because the system runs at too much pressure or bangs every time a valve closes. The plumber checks static pressure with a gauge, tests or replaces a failing pressure reducing valve, and can add hammer arrestors so the new repair is not under the same stress.
Repair clamps and pipe wraps can hold a break long enough to get the water back on, which is sometimes the smart call in the middle of the night. It is not a permanent repair inside a closed wall. Ask the plumber which one you are getting, and if it is temporary, get the follow-up visit on the written scope.
Once the permanent repair is in, the contractor pressure tests the line, usually by restoring the water, closing fixtures, and watching a gauge or the meter for any drop. Only then does the wall get closed or the drying start in earnest.
Stay on the line and we will talk you through the shutoff while a plumber is located.
Here is what happens after you call, in the order it usually happens.
First we help you stop the water. The house main is usually where the line enters the home: a basement wall, a utility closet, a garage, or near the water heater. If that valve is stuck or missing, the meter valve or curb stop at the street can close it, and some utilities ask that their crew operate the curb stop. Then we route the call.
Once on site inside the confirmed window, the plumber verifies the shutoff is holding and the leak has stopped. Expect no water for a while; the goal is to restore service the same visit when the repair allows it.
The plumber locates the failure, checks what type of pipe it is and why it broke, and maps the wet area with a moisture meter. You get a written price for the pipe repair and, when drywall, insulation or flooring is wet, a referral to a restoration contractor for extraction and drying.
After the repair, the line is pressure tested, the water is restored, and the plumber walks you through what was done. You sign off on the completed scope, keep the written invoice and photos for your insurance claim, and ask about the contractor's workmanship warranty before they leave.
A fixed pipe does not dry a wet wall. Water from a supply line is usually Category 1 clean water at first, but it starts to degrade if it sits, and mold can begin within 24 to 48 hours. Drywall wicks water upward, insulation holds it, and hardwood cups as it absorbs moisture from below.
When the plumber finds wet materials, a restoration contractor can bring extraction gear, air movers, and LGR dehumidifiers, then log moisture readings each day until the materials reach dry standard. Adjusters usually want those logs.
Each card is a common pattern from the calls this line takes, written up as a typical scenario.
A homeowner notices a bulge in the hallway ceiling the first warm morning after a cold snap. The PEX line in the attic split where it ran above the insulation near the eaves. The plumber replaces the damaged section with expansion fittings, pressure tests it, and suggests rerouting the line below the insulation.
A caller shuts the main to stop a leak under the kitchen sink, but the old gate valve breaks and the water keeps coming. The dispatcher walks them to the meter box. Once the plumber arrives, they repair the leaking CPVC fitting and replace the failed gate valve with a quarter-turn ball valve so the next shutoff is simple.
A family hears water running with every faucet closed and finds a warm spot near the bathroom. The plumber confirms the meter moves with all fixtures off, then uses acoustic and thermal equipment to locate a pinhole in a copper line under the slab. They price both a spot repair and a reroute, and the homeowner chooses the reroute.
A property owner calls about another burst fitting on the laundry line. The plumber measures static pressure well above what fixtures are built for and finds a failed pressure reducing valve. Replacing the valve and repairing the fitting addresses the cause instead of patching one more joint.
These are typical situations callers describe, not quotes from specific customers.
Check where the supply line enters the house: a basement wall, a utility closet, the garage, or near the water heater. If that valve is stuck or broken, the meter valve or the curb stop at the street can shut the water off, though some utilities prefer to operate the curb stop themselves.
Closing the main shuts off every fixture, so no water is normal until the leak is isolated. In many cases the plumber caps the damaged line or adds a shutoff on that branch, which lets the rest of the home come back on quickly.
A pipe that froze once is likely to freeze again unless the conditions change. Ask the contractor about moving the line to a warmer wall, insulating it, adding heat cable, and sealing the drafts that let cold air reach it.
Usually not. A clamp can stop a leak in an emergency, but inside a closed wall the plumber should make a permanent soldered, crimped, pressed, or expansion repair. If you get a temporary fix first, have the follow-up written into the scope.
If water reached drywall, insulation, subfloor, or carpet pad, yes. Those materials hold moisture long after the surface feels dry, and mold can start within 24 to 48 hours. A restoration contractor measures the moisture and dries it with air movers and dehumidifiers.
Coverage depends on your policy. Sudden pipe breaks are commonly covered for the resulting water damage, while the repair of the pipe and long-term leaks often are not. Document everything with photos and keep every written invoice for the adjuster.
Calls from Sangaree and nearby communities in Sangaree, SC are routed to independent plumbers who work in the area.
Single-family homes, townhomes, and condo units, including breaks that leak into a neighbor's unit below.
Landlords and property managers dealing with a tenant call at night and a shared riser or branch line.
Small commercial spaces where a burst line in a restroom or break room shuts the business down.
Free referral call, any hour, with your arrival window confirmed before you hang up.
